what can be used for pontoon transom in place of plywood

How to Replace a Boat Transom Board with Richlite Intectural

May 26, 2015 The original wood transom support board on this customer's boat had rotted and Think you could use Piece-o-Sheet for your next project?

3/4 in. x 4 ft. x 8 ft. AB Marine Grade Pressure-Treated Fir Plywood

Can you paint/prime the wood immediately after buying, or does the chemical treatment have to dry out for some .. I used it on the deck of my pontoon boat.

Repairing Fiberglass Powerboat Transoms - Epoxyworks

Jul 26, 2014 The effects of the motor's weight are magnified when the boat is accelerated These factors have a cumulative effect on structural failure. If the total area of fiberglass repair can be confined to the transom and not allowed to If you will be removing the entire plywood core, use whatever combination of

Recomendations for new transom material? Boat Design Net

Marine Plywood vs. monolithic lumber vs. some kind of composite vs. to use composites and core material in "smaller boat" transoms with

Pontoon Makeover: How to Update a Pontoon Boat - Cabin Life

Typically built from aluminum (frame and pontoons) with a wood deck, Also, replacement furniture specialists have become commonplace in the past five years or so. Check carefully around the transom – where it's welded to the boat deck You may have to use straps and come-alongs to gently force the boat into a

Capt. Pauley's Boat Shop: Replacing a transom from start to finish

Jun 24, 2011 You can use top-of-the line marine plywood or lumberyard exterior ply. The transom should be bonded in place using epoxy resin and

Re-Deck, Carpet & Floor Vinyl - Marsh Brothers, Inc.

Marsh Brothers specializes in Re-Decking Pontoon And Boats With New Carpet Or New Floor Vinyl. This Restoration Would Be New From The Tubes Up. New Plywood, Carpet Or Floor Vinyl Transom Is Where An Outboard Motor Is Mounted. We Use And Stock OEM Replacement Steering Systems, Manufactured By

plywood over existing boat floor - Carpet Connection

Plywood bow deck replacement - '63 Tolycraft Roustabout frame of the boat and up through a Your best bet is to use marine-grade plywood to refurbish your pontoon deck. Transom Replacement With a Plywood Core - Instructables.

Transom wood for my aluminum boat Page: 1 - iboats Boating Forums

Sep 12, 2011 Also I know not to use treated wood of any kind unless its marine specific. . You probably won't find a suitable epoxy at a local place and you'll have Does your dads boat have angle brackets from the transom to the floor?

Transom Wood Replacement Options on the Cheap? - Glen-L.com

Jan 19, 2013 The boat only has a 35hp on it so strength isn't a huge concern, just want to If I use any of the untreated woods I would be using liquid nail to fasten motor clamps, motor bolts, and trim plate to hold transom wood in place.

Pontoon Construction Sylvan Marine

The transom area is supported with up to 3/16" hat-channel construction using Other manufacturers use C-channel designs which can require more cross by Endurance - 3/4", 7-ply marine treated plywood through=bolted and screwed to

Transom Replacement With a Plywood Core: 9 Steps (with Pictures)

Apr 16, 2012 Picture of Transom Replacement With a Plywood Core In our example boat, you can see the transom core is soaked and it has lost nearly all of its stiffness. You will use this template to cut your transom core and also to

How to Seal Marine Plywood DoItYourself.com

If you have a boat or are planning on building something that will be submerged in With normal plywood you would use two coats of sealer, maybe even three.

Transom Replacement - Starboard Marine

The transom of a power boat is the strongest part of the vessel. It has to The problem is that most boat manufacturers do not use treated plywood. Fiberglass

Boat Repair: Alternative transom, deck and stringer - Lake Expo

Jul 8, 2011 It also seems to have use in replacing rotted decks and stringers. I want to The plywood and wood backers can be clamped in place or held

Rebuilding a Transom - Interlux - Jamestown Distributors

On the boat shown in Figure 1, it took an entire day to remove the wood in the flange by here, a single piece of marine grade plywood could not be dropped into place. Once the transom is smooth, you can use either a mixture of epoxy and